韩国 LG-EZ 模拟示波器 OS3060D

产地：韩国

厂商：韩国LG-EZ

市场价格：

我们价格：

Main Features

·	60MHz, 2Ch, Dual trace, 20M sampling/sec
·	Combination of analog and digital oscilloscope performance.
·	Maximum 2-channels simultaneous sampling rates of 20MS/s.
·	Digitized 20MHz repetitive signal equivalent mode
·	2 K words memory capacity per channel
·	One-touch switching real time and storage modes
·	Two save memories
·	Pre-triggering enable observation of waveform portion before the trigger point.
·	Roll mode provides continuous observation of slow waveforms
·	An averaging function provides summation averaging up to 256 times
·	Linear and sine interpolation function for optimum pulse or sinusoidal signals
·	Magnification function simplifies detailed waveform observation
·	CRT readout for displaying set values along with measured voltage, time and frequency using the cursor function
·	Direct copy of screen display using HP-GL commands with RS-232C interface Delay signal function



CRT	- Configuration and useful screen : 6 inch rectangular screen with internal graticule, 8X10div.(1div = 1cm) marking for measurement of rise time, 2mm subdivisions along the central axis. - Acceleration potential : +1.9kv approx.(ref. Cathode) - Phosphor : P31 - Focusing : provided - Trace rotation : provided - Scale illumination : provided - Intensity control : provided

Z-AXIS INPUT (INTENSITY MODULATION)	- Input signal : positive going signal decreases +5Vp-p or more signal cases intensity noticeable modulation at normal intensity setting - Bandwidth : DC to 3.5MHz(-3dB) - Coupling : DC - Input impedance : 20kз - 30kз typical - Maximum input voltage : 30V(DC + peak AC)

VERTICAL DEFLECTION	- DC coupled(-3dB) : DC to 60MHz normal / DC to 10MHz magnified - AC coupled(-3dB) : 10Hz to 60MHz normal / 10Hz to 10MHz magnified - Modes : CH1, CH2, ADD, DUAL (CHOP : Time/div. switch from 0.2s to 5ms, ALT : Time/div. switch from 2ms to 0.1レs) - Deflection factor (normal): 5mV/div. to 5V/div. in 10 calibrated steps of 1-2-5 sequence. Continuously variable between steps at least 1:2.5 - Deflection factor (5MAG) : 1mV/div. to 1V/div. in 10 calibrated steps - Accuracy : normal 【3%, magnified : 【5% - Input impedance : approx. 1Mз in parallel with 30pF【3pF - Maximum input voltage : direct 250V (DC + peak AC) - Input coupling : AC, GND, DC - Rise time : 5.8ns or less (35ns or less in 5MAG) - CH1 output : 20mV/div. into 50з / DC to 10MHz(-3dB) - Polarity inversion : CH2 only - Signal delay : delay cable installed

HORIZONTAL DEFLECTION	- Sweep mode : A, A int B, B, B triggered, X-Y - Time base A : 0.1レs/div. to 0.2s/div. in 20 calibrated steps of 1-2-5 sequence uncalibrated continuous control between steps at least 1:2.5 - Hold-off time : variable with the hold-off control - Time base B : 0.1レs/div. to 10レs/div. in 7 calibrated steps of 1-2-5 sequence uncalibrated continuous control between steps at least 1:2.5 - Delayed sweep : 1 div. or less to 10 div. or more - Delayed time jitter : better than 1:20,000 - Sweep magnification : 10 times(maximum sweep rate : 10ns/div.) - Accuracy : 【3%, additional error for magnifier : 【2%

TRIGGER SYSTEM	- Modes : AUTO, NORM, TV-V, TV-H - Source : CH1, CH2, LINE, EXT - Coupling : AC - Slope : + or - - Sensitivity and frequency in AUTO, NORM 20HZ - 2MHz : 0.5div. in INT / 0.15Vp-p in EXT - Sensitivity and frequency in AUTO, NORM 2Hz - 60MHz : 1.5div. in INT / 0.3Vp-p in EXT - TV-V, TV-H : at least 1div. or 1.0Vp-p - External trigger input impedance : 1Mз - Maximum input voltage : 250V (DC + AC peak)

X-Y OPERATION	- Single trace X-Y : X-axis = CH1(SA), Y-axis = CH2(SB) - Dual trace X-Y : X-axis = CH1, Y-axis = CH2 - Sensitivity : 1mV ~ 5V/div. 【 5% - X-Y phase difference : 3∑ or less as DC to 50kHz

READOUT FUNCTION	- Cursor readout function : ツV, voltage reference ツ-REF, ツT, time reference ツ-REF, ツ1/T, frequency reference ツ-REF - Effective cursor range from center graticule : within 【3div. on vertical / within 【3div. on horizontal - Resolution : 1/25 div.

DIGITAL STORAGE FUNCTION	- Display / save memory : 1000 words / channel or 1000 words / channel X 2 - Acquisition memory : 5レs/div. to 20s/div. : 2000 words / channel or 0.1レs/div. to 2レs/div. : 1000 words / channel - Vertical resolution : 25 point / div - Horizontal resolution : 100 point / div - Maximum sampling rate : 20M sampling / sec - Digital bandwidth single shot event : 5MHz - Repetitive event : 60MHz - Data acquisition method : NORM mode(storage the data each time trigger) / AVG mode(averaging form 4 to 256 times) / ROLL mode(data is continuously stored on the CRT) /HOLD mode(data is held for the NORM, AVG or ROLL) / SINGLE mode (waveform is held after stored) / AMAG mode(simultaneously displaying the original waveform and its magnified waveform) / GNG mode(judgement and comparing of acquisition signal) - Data save : up to two storage data can be saved. Saved data can be recalled to the display whenever required. - Pre-trigger : variable (0.04 div. step) - Plotter : plotter output of the CRT displayed information to an HP-GL plotter via RS-232C interface - Data output : RS-232C - Magnified display : X 10 by time/div. switch or MAG switch - Sweep time : 0.1レs/div. to 20s/div. (repetitive signal: 0.1レs/div. to 2レs/div.) / roll mode : 0.5s/div. to 20s/div. / ALT mode : 0.1レs/div. to 0.5ms/div. / CHOP mode : 1ms/div. to 20s/div.

CALIBRATOR	- Probe adjustment : approx. 1kHz frequency, 0.5V(10%) square wave with 40-50% duty ratio

POWER SUPPLY	- Line voltage range : 100V(90-110V) with 250V 2A fuse, 120V(108-132V) with 250V 2A fuse, 220V(198-242V) with 250V 1A fuse or 230V(207-250V) with 250V 1A fuse - Line frequency : 50/60Hz - Power consumption : approx. 70W

PHYSICAL CHARACTERISTICS	- Weight : 8kg - Dimension : 320mm(W) X 140mm(H) X 430mm(L)

OTHERS	- Accessories including : Operation manual, Spare fuse, Power cord - Optional accessories (sold separately): Probe, RS-232C software package (LS-3000)